The speed limiter regime in Singapore aims to improve road safety and driving behaviour. It complements other measures intended to reduce fatalities and injuries among all road users.
Under Singapore’s laws, it is mandatory for speed limiters to be installed in the following categories of vehicles:
- every goods vehicle having a MLW exceeding 12,000kg and which has, or if a speed limiter is not fitted to it would have, a maximum speed exceeding 60km/h; and
- every public service vehicle having a MLW exceeding 10,000kg and which has, or if a speed limiter is not fitted to it would have, a maximum speed exceeding 60km/h.
Currently, lorries with a MLW between 3,501kg and 12,000kg (inclusive) are not required by law to have any speed management devices, or speed limiters. The law to have speed limiters will be expanded to all lorries in this weight category progressively over 1 January 2026 to 1 July 2027.
From Singapore Limiter Announcement
https://www.police.gov.sg/Advisories/Traffic/Traffic-Matters/Speed-Limiter-Announcement
GPS Speed limiter features:
1 Speed Limiter
Enforce to limit the speed of your vehicle if preset maximum speed
2 Tamper proof
Maximum speed is 40km/h if maximum speed is tampered or sensor is cut.
3 Download data
Data can be stored for 72 hours at interval of 5 seconds.
Data can be retrieved by connecting device to computer via USB data port
4 Bluetooth Printer
Violations can be printed out for the last one-hour driving. Portable printer prevents drivers from printing
Speed violations can be printed
5 Violations alarm
All violations will be transmitted to platform.
6 Over speed alarm
When vehicle reaches 95% of preset speed limit, built-in buzzer shall make sound alarm to warn driver.
7 Fuel monitoring (optional)
Monitor vehicle fuel consumption. Need connect with fuel sensor that gives out analog voltage.
Real time fleet tracking Working power: 2W
GPS speed limiter specs:
|
Name |
UT04S GPS Speed Limiter |
|
Weight |
191g |
|
Dimension |
110*75*30 mm |
|
Working voltage |
DC 9V-36V |
|
Backup battery |
800mAh 3.7V |
|
Battery working time |
4hrs |
|
Working current |
60~150mA |
|
Standby current |
16mA |
|
Charging current |
Max < 500mA |
|
Input Fuse |
2A |
|
Working power |
2W |
|
Working Temp. |
-45~85℃ |
|
GSM Frequency |
850/900/1800/1900 Mhz |
|
Max RF output |
33.0dBm±2dBm |
|
Dynamic input range |
-15 ~ -102dBm |
|
GPS chipset |
Ublox 7 |
|
GPS frequency |
L1, 1575.42 MHz |
|
GPS accuracy |
5 meters at 2D RMS |
|
Interface |
1 A/D Port for fuel monitoring |
|
1 Interface for data config by PC |
|
|
1 USB port for USB disk data download |
|
|
2 Port for speed limit |
|
|
1 Input for speed signal |
|
|
1 Input for Bluetooth Printing control |
|
|
Built in Flash |
Store data of last 72hrs, above 5000 points |
|
Built in Buzzer |
Sound alarm when speed reaches 95% of set value |
|
Alarm |
External power cut, Lower battery, Over speed, Geo-fence |
|
Tracking method |
Real time on Web Software and Phone APP |
|
Account level |
Unlimited sub account management |
|
Report |
Trip report, Speed report, Geo-fence report, Parking report, Driving Report, Alarm report, Mileage report, Engine Idle report |
GPS speed limiter connection:
ACC: (Orange) connected to vehicle ACC wire to detect engine ON/OFF
PULSE: (Purple) connected to vehicle speed signal wire to detect speed
GND / DC+: (Red and Black) connected to battery positive and ground.
GND / SOS: connected together with SOS button to control wireless printing. (With wireless Bluetooth printer turned on, press SOS button for 3 seconds, device shall beep, in 15 seconds device shall print last 1 hr data including over speed data. Long beep once all data is printed.)
NC / NO: (Green / Yellow) cut off fuel pump power wire, connect NO Yellow wire to the cut point, working as a power supply to fuel pump. (Relay and buzzer are built-in, when speed reaches 95% preset value, beep; 100% speed reached, built-in relay is activated with continuous beep.
Fuel (Grey) connect with fuel sensor signal wire to monitor fuel consumption (Optional)
SIM slot: insert SIM card
Micro USB: connect device to PC for config
USB disk: insert USB disk for data download (beep sound after inserting, long beep once all data is downloaded.)
SW: built-in backup battery switch. (Default OFF)
RESET: one click to restart device
LED: Blue for GPS (ON if signal okay), Green for GSM (slow flash if signal okay)